Omega Vehicle Security Stud Sensor DP25 TH User Manual

START HERE  
2
3
4
Turn on the Unit  
Using This Quick Start Manual  
To Change the Input Type:  
Connecting the Sensor Input  
1. Apply power to the unit. The unit initializes,  
flashing ÒTHERMISTORÓ. Then the temperature  
should appear.  
Use this Quick Start Manual to set up your controller  
and begin operation. Information is provided on how to:  
1. Press MENU until the display  
1. Locate the TB2 (TB3 on Version #1) connector on  
the rear of the unit.  
shows ÒINPTÓ:  
¥
¥
¥
Connect ac power  
2. Connect sensors, referring to the appropriate  
diagram below and tighten down lockdown  
screws.  
/MAX  
SETPTS  
/MIN  
MENU  
RESET  
2. Verify that a temperature is displayed. If not:  
Connect sensor input  
Set basic options for operation  
¥
¥
¥
¥
Remove ac power  
2. Press /MIN to show current input  
3. Tug gently on the wires to verify the connections.  
4. Replace the panel at the back of the unit.  
Verify the TB1 power connections  
Check your power source  
Apply power again  
For complete information on all setup options, see the  
OperatorÕs Manual.  
type:  
/MAX  
SETPTS  
/MIN  
MENU  
RESET  
Before You Begin  
1
2
3
In addition to the controller and the related parts, you  
will need the following items to set up your unit:  
3. Press /MAX to select the setting.  
+S  
-S  
-R  
Configure the Unit  
To configure the unit, use the buttons on the controllerÕs  
front panel.  
Choices are: 4004, 4005, 4006,  
4007, 4008, 4017, 4018 and 700.  
¥
¥
¥
ac power  
/MAX  
SETPTS  
/MIN  
MENU  
RESET  
Sensor  
1Ú8Ó flat blade screwdriver  
4. Press MENU to store the value.  
PANEL THICKNESS  
6,4 (.25) MAX  
0,8 (.03) MIN  
To:  
Take This Action  
5. Press RESET twice to display the current  
2-Wire Input (400 Series)  
temperature.  
Mount the Meter  
1. Cut a panel opening  
using the dimensions  
shown to the right.  
Display the  
Configuration  
Menu.  
Press the MENU button.  
The first function on the  
menu, ÒINPTÓ, displays.  
1,5  
R(.06)  
4 PLCS  
45,00 + 0,61/-0,00  
(1.772 + .024/Ð.000)  
1
2
3
/MAX  
/MAX  
SETPTS  
/MIN  
MENU  
RESET  
SETPTS  
/MIN  
MENU  
RESET  
92,00 + 0,81/Ð0,00  
(3.622 + .032/Ð.000)  
Select the  
submenu  
function.  
1. Press MENU until the  
function you want is shown.  
+S  
-S  
-R  
2. Position the unit in the  
opening, making sure  
NOTE: Dimensions in Millimeters (Inches)  
2. Press /MIN.  
the front bezel is flush with the panel.  
To Change the Decimal Point:  
Select a value  
for that submenu  
function.  
1. Press /MAX. to display  
the option you want.  
2. Press MENU to select it.  
ÒSTRDÓ quickly flashes,  
indicating that the selection  
has been stored in memory.  
Then the next menu function  
displays.  
1. Press MENU until the display  
Connect ac Power  
shows ÒDEC.PÓ:  
Warning: Do not connect ac power to your meter  
until you have completed all input and output  
connections. Failure to do so may result in injury!  
/MAX  
SETPTS  
SETPTS  
SETPTS  
/MIN  
MENU  
MENU  
MENU  
RESET  
RESET  
RESET  
3-Wire Input (700 Series)  
Hook up Alarm 1 (Setpoint) (refer to TB1 Main  
ac Power Connection Drawing)  
2. Press /MIN to show the current  
1. Remove the panel at the back of the unit.  
2. Locate the TB1 connector.  
decimal point location:  
Go back to the  
previous menu  
function.  
Press RESET once.  
1. Connect a jumper from ac Line (Terminal 7) to  
Relay 1 Common (Terminal 3).  
/MAX  
/MIN  
3. Insert the correct wire in each terminal as shown  
in the following figure and tighten the lockdown  
screws. Tug gently on the wires to verify  
connections.  
2. Connect Relay 1 Normally Open (Terminal 1) to  
External Alarm ac Line.  
Exit the  
Configuration  
Menu.  
¥
¥
Press RESET twice. The  
unit reinitializes (displays  
ÒRSTÓ, then ÒTHERMISTORÓ).  
When the temperature  
displays, the meter is back in  
Run Mode.  
3. Press /MAX to select the setting.  
VERSION #1  
VERSION #2  
Choices are: ÒFFF.FÓ, ÒFFFF.Ó or  
ÒFF.FFÓ.  
3. Connect External Alarm to ac Neutral (Terminal 8).  
/MAX  
/MIN  
TB1  
4. Press MENU to store the value.  
Hook up Alarm 2 (Setpoint) (refer to TB1 Main  
ac Power Connection Drawing)  
1
2
3
4
5
6
1
2
3
4
5
6
TB2  
5. Press RESET twice to display the current  
1
2
3
7
8
9
10 11 12  
1
2
3
7
8
9
Optionally, you can press  
MENU to move through all  
the menu functions until the  
meter reinitializes.  
temperature.  
1. Connect a jumper from ac Line (Terminal 7) to  
Relay 2 Common (Terminal 6).  
EARTH  
GROUND  
NEUTRAL  
LINE  
2. Connect Relay 2 Normally Open (Terminal 4) to  
External Alarm ac Line.  
AC POWER  
/MAX  
/MAX  
SETPTS  
/MIN  
MENU  
RESET  
SETPTS  
/MIN  
MENU  
RESET  
FUSE  
3. Connect External Alarm to ac Neutral (Terminal 8).  
Main ac Power Connections  
 

Miele Ventilation Hood DA 1160 User Manual
Milwaukee Power Screwdriver 6580 20 User Manual
Minolta Digital Camera Dynax 7 User Manual
Moxa Technologies Switch Uport 1200 1400 1600 User Manual
National Instruments Network Card NI PXI 8104 User Manual
Nikon Binoculars Monarch Gold E User Manual
Nvidia Computer Hardware N61P User Manual
Oki Network Card C6100dn User Manual
Orion Car Audio Speaker XTRPRO102 User Manual
Panasonic Air Compressor DC66C10RCU6 User Manual