Omega Vehicle Security Automobile Alarm K9 6ATV2 User Manual

Ta ble Of Con ten ts  
Introduction ...................................................................................................... 3-4  
Advanced System Features............................................................................... 4-5  
Transmitter Operations ........................................................................................ 6  
Arming the System Using the Transmitter ....................................................... 7-8  
Passively Arming the System ........................................................................... 8-9  
Security System Armed and Triggered........................................................... 9-11  
Disarming the System................................................................................... 11-12  
Remote Panic Feature ........................................................................................ 13  
Optional 2nd Channel Output (Trunk Release) and 3rd Channel Output .... 13-14  
Using the Valet Switch ................................................................................. 14-16  
Red LED Status Indicator............................................................................. 16-18  
Audible and Visual Indications ........................................................... 18-19 & 22  
Auxiliary Optional Sensor Port with Prewarn .............................................. 22-23  
Anti-Carjacking Protection ........................................................................... 23-24  
Optional Pager Unit and Backup Battery .......................................................... 25  
Programming Transmitters ........................................................................... 25-26  
Programming Features.................................................................................. 27-29  
Features Programming Checklist.......................................................... Centerfold  
Programmable Features ................................................................................ 29-38  
Transmitter Options ........................................................................................... 39  
OWNER'S MANUAL  
for  
K9-6ATV2  
One or more of these patents may apply to this product:  
#5,612,578 #5,612,699 #5,654,688 #5,663,704 #382,558 #385,878  
#5,719,551 #5,729,191 #5,739,748 #5,750,942 #5,818,329 #5,739,747  
COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT, INC. 1999  
The Red LED Status Indicator: Informs you of the different conditions the  
security system can be in and also serves as a visual deterrent to break-ins and theft.  
In tr od u ction  
Congratulations on your purchase of your new vehicle security system and on  
joining over 8 million people worldwide who have trusted their vehicle's security  
to the designers of Omega Research & Development, Inc. To learn how to operate  
your security system, please become familiar with the following three principal  
user components: the Remote Transmitter, the Red LED Status Indicator and the  
Valet Switch.  
The Valet Switch: This switch is used for several purposes, one which is being  
used to place the system into "Valet Mode". Valet Mode can be used to turn off  
automatic functions, such as Last Door Arming or Automatic Rearming. The Valet  
Switch is also used, with the ignition key, to disarm the security system in the event  
the transmitter becomes inoperable, and this switch is also used in the procedure for  
programming features and learning transmitters.  
The Remote Transmitter: Each security system includes two pre-learned  
transmitters, but if desired up to 4 different transmitters can operate the system. The  
transmitter has three buttons: one large button in the middle and two smaller  
buttons, one on either side. This system is pre-programmed to have the transmitter  
buttons work in the following configuration:  
Please spend time reviewing this guide to become familiar with your new  
Omega vehicle security system. You will find that your new vehicle security  
system will give you years of trouble-free convenience and protection.  
Ad va n ced System Fea tu r es  
The large button is used to arm, disarm and panic the security system.  
AutomaticTransmitterVerificationTM (ATV): YourOmegavehiclesecurity  
system is protected against a common weakness found in all remote controlled  
security systems, and even factory-equipped Remote Keyless Entry systems. This  
weakness is the ease in which an additional transmitter may be programmed to  
operate the system. This vulnerability allows a thief to code his own, unauthorized  
Page - 4  
The small right button is used to operate the 2nd channel output, typically used  
for trunk release, and arm and disarm the system without the audible chirps.  
The small left button operates the 3rd channel output and, in conjunction with  
the large button, can remotely bypass a sensor upon arming.  
Page - 3  
 
* The electronic siren features six different tones, and every 5 seconds the siren will change  
the tone to generate more attention to the vehicle. The vehicle's horn may be used if desired.  
The horn, if used, will honk on and off for 10 seconds, then pause for 5 seconds, repeating  
this cycle for the duration of the activated alarm period. This prevents the horn from  
overheating. Please ask the installer for details on utilizing the horn.  
Additionally, Automatic Last Door Arming may entitle you to an insurance  
discount. Please note that the previously mentioned Arming By-Pass feature does  
not operate with the Automatic Last Door Arming feature. The bypass feature is  
designed to operate only when arming the system with the transmitter and all  
protected entries must be closed to initiate the Automatic Last Door Arming  
sequence. Last Door Arming does not effect the operation of Active Arming.  
To prevent the system from automatically arming while the vehicle is being  
refueled you have these options: put the system in Valet Mode (page 14), keep your  
door open, or turn on your dome light switch so the system detects that your door  
is still open. We do not recommend leaving your ignition key turned "on".  
The sirenandthe parking lightswill stayactive for60secondsunless youdisarm  
thesystemwiththetransmitterortheValetSwitch. Ifallprotectedentriesaresecure  
at the end of 60 seconds, the system will stop and rearm automatically to detect  
another entry attempt. If there is a protected entry still open or if an optional sensor  
is still in a triggered state at the end of 60 seconds, the system will reactivate for two  
more 60 second cycles. In this case the system will stop after a total of 3 minutes  
and rearm automatically, while ignoring only the open entry or triggered sensor.  
When the entry is closed or the triggered sensor is reset, protection will begin  
instantly for the formerly affected circuit.  
Oncethesecuritysystemhasbeenactivatedandreset,thedisarmingconfirmation  
willnolongerbe2sirenchirps,andtheparkinglightsstayingon.Instead,thesystem  
will respond with 4 siren chirps and the parking lights flashing 4 times before  
staying on for 30 seconds. The LED Status Light will change to flashing one to four  
times between pauses to indicate which protection circuit triggered the system.  
These audible and visual indications will remain until the ignition is turned “on”.  
Page - 10  
Secu r ity System Ar m ed An d Tr igger ed  
While the security system is armed, the LED Status Indicator will be flashing.  
Should any intrusion attempt occur, your system will instantly "trigger". Once  
triggered, the security system will respond by:  
1) The electronic siren will sound*.  
2) The parking lights will flash on and off for the duration.  
3) The doors will relock. This feature is so unique that the security system can  
detect an open door and wait until the door is closed; at that time the door  
re-locks so that the thief cannot easily regain entry.  
Page - 9  
instantly disarm the system and unlock the doors. If you have the optional unlock  
driver's door feature, then upon disarming only the driver's door will unlock, and  
if the large transmitter button is pressed again within 5 seconds, or at any time if a  
door is open, all of the other doors will unlock.  
Disarming is confirmed by the siren chirping twice, and the parking lights  
turning on for 30 seconds. However, the lights will turn off instantly if the ignition  
switch is turned "on". If the system was triggered and reset while you are away, the  
disarm confirmation will change to 4 siren chirps, 4 light flashes, and then the lights  
will stay on for 30 seconds. The security system will have this response upon  
disarming until the ignition switch is turned "on", which clears the unit's memory.  
Anytime the security system triggers, the LED Status Light will indicate which  
zone triggered the system by flashing one to four times, pausing between flashes.  
This code will continue to flash, even after disarming. The system can hold two  
different violation codes in it's memory, which is cleared by turning the ignition  
switch "on".  
Safety Disarm/Storm Mode: While the system is activated, i.e. sounding the  
siren and flashing the lights, pressing the large transmitter button will disarm the  
system only. The system will not chirp twice or illuminate the parking lights, nor  
unlock the doors if the system is configured to also operate the door locks. This  
safety feature ensures that the vehicle remain secure should the system require  
disarming due to being activated from nuisance or malicious false sensory inputs,  
such as typically produced by severe weather conditions. To remotely unlock the  
doors if the system is disarmed while activated, repeat the arm/disarm operation by  
pressing and releasing the large transmitter button once, then again. If disarmed  
from a panic mode, the normal disarm indications are present, including the  
unlocking of the doors.  
Automatic Rearming Feature: Should you unknowingly press the transmitter  
button, which will result in your system disarming, the system can automatically  
rearm itself 90 seconds later and once again lock the doors. This feature is  
programmable, and may be turned off.  
Automatic Rearming can be paused by opening the door or stopped by turning  
"on" the ignition switch. Also, Automatic Rearming can be cancelled by the Safety  
Disarm/Storm Mode feature; if the system is disarmed while triggered, Automatic  
Rearming will not occur. Automatic Rearming is confirmed by a fast flashing LED  
StatusIndicatorafterdisarming, unlessthesystemwastriggeredandreset, inwhich  
Disa r m in g Th e System  
Disarming The System Using The Transmitter: While the security system is  
in the armed state, pressing and releasing the large transmitter button once will  
Page - 11  
case a Zone Violation code will flash instead.  
Page - 12  
 
Optional 3rd Channel Output: This output's operation is similar to the trunk  
release output except for the following: press the small transmitter button on the left  
for 2.5 seconds to activate the 3rd channel output. The 3rd channel output will  
operate regardless of the ignition switch being "on" or "off", and there is no audible  
or visual confirmation. This output can be used to operate optional equipment such  
as remote car starters or window roll-up modules.  
Rem ote P a n ic Fea tu r e  
Remote Panic Activation From The Transmitter:Should you feel threatened  
or the need to attract attention you can activate your system's Remote Panic feature  
at any time by depressing and holding the large transmitter button for 3 seconds.  
Your system will respond by sounding the siren, locking the doors and flashing the  
exterior and interior lights for the normal activated period of 60 seconds. Should  
wish to enter your vehicle or disengage Remote Panic, simply press and release the  
large transmitter button.  
Usin g Th e Va let Switch  
The primary function of the Valet Switch is to enter your security system into  
ValetMode, whichpreventsthesystemfromarming. Youwillfindthisusefulwhen  
stopping at service stations, having your vehicle serviced, having your car valet  
parked or while having your car washed. The Valet Switch, in conjunction with the  
ignition key, can be used to disarm the system should your transmitter be lost or  
become inoperable. The Valet Switch is typically mounted in same housing as the  
LED Status Indicator. However, some custom installations may have the Valet  
Switch mounted in a hidden location; if so, be sure your installing dealer indicates  
the location of the Valet Switch to you to avoid potential inconvenience.  
Option a l 2n d Ch a n n el a n d 3r d Ch a n n el Ou tpu t  
Optional 2nd Channel Output (Trunk Release): If your vehicle is equipped  
with electric trunk release, your installing dealer can configure your system to  
accomplish trunk release from your transmitter. Use of the 2nd channel output is  
recommended to operate this option; simply press and hold the small transmitter  
button on the right for 2.5 seconds. Your vehicle will respond by releasing the trunk  
lidorrearhatch, chirpingthesirentwice, disarmingthesystem, unlockingthedoors  
and turning on your parking lights for 30 seconds. The trunk release will not operate  
with the ignition switch "on" unless the vehicle's door is open. If desired, the  
security system can be programmed to remain armed when this feature is used.  
Page - 13  
Normal Valet Mode: This unique feature can be activated anytime the system  
is disarmed and allows you to enter the Valet Mode by simply depressing and  
Page - 14  
holding the Valet Switch, provided the system is not armed. If the system is armed  
orinthetriggeredstate,however,theignitionmustbeturned"on"andthentheValet  
Switch must pressed within 5 seconds to disarm the system and enter Valet Mode.  
While the system is disarmed, simply press and hold the Valet Switch for 2  
seconds to activate the Valet Mode. The system will confirm that it is in the Valet  
Mode by chirping the siren twice, and the LED Status Indicator will illuminate  
steady Red. The security system will stay in the Valet Mode when the ignition  
switch is "on" or "off". While in the Valet Mode, although the system will not arm,  
the transmitters will still operate the Remote Panic feature, the doorlocks, and trunk  
release; the doors will also lock when the ignition switch is turned "on" and unlock  
when it is turned "off"'. While the security system is in the Valet Mode, every time  
the ignition switch is turned "off", the siren will chirp once as a reminder.  
STEP 1. With the system in the armed condition, enter via the driver's door (be  
aware that the security system will trigger the when the door is opened).  
STEP 2. Use the ignition key to turn the ignition switch "on".  
STEP 3. Within 5 seconds, press the Valet Switch. The system will disarm.  
Red LED Sta tu s In d ica tor  
The LED Status Indicator feature is a visual indication of what state the security  
system is in at any given time. The LED Status Indicator is normally positioned in  
alocationthatiseasilyobservedbythedriver. Thesearethepossibleconditionsthat  
the security system can be in as reflected by the LED Status Indicator:  
1) Off  
= The security system is disarmed and not performing any  
automatic functions.  
= The security system is in the Valet Mode.  
= The security system is Fully Armed.  
= The 30 second Last Door Arming feature or 90 second  
Automatic Rearming feature is in progress. This fast  
flashing also occurs during the 3 second or 45 second  
To Exit Valet Mode: Simply press the Valet Switch, and instantly the security  
system will exit Valet Mode. To confirm that the Valet Mode is turned off, the LED  
Status Indicator will turn off.  
2) On Constant  
3) Flashing Slow  
4) Flashing Fast  
Disarming The Security System If The Transmitter Is Lost: In the event the  
transmitter is lost, damaged, or its batteries become exhausted, the Valet Switch  
and your ignition key can be used to disarm the system:  
arming delay.  
Page - 15  
Page - 16  
 
Automatic Transmitter VerificationTM: After the ignition is turned "on", the  
LED Status Indicator will flash and pause to indicate the number of transmitters  
programmed to operate your security system. For example: two flashes and pause  
indicates that only two transmitters are encoded to operate your system. Whenever  
youleave yourvehicleandkeyswithsomeone,youwillnowhavethepeaceofmind  
in knowing that only your transmitters will operate the security system and that no  
additional transmitters have been coded into your system for the purpose of stealing  
yourvehicleoritscontents.ThisIndicatorflashingoccursfor10secondseverytime  
the ignition switch is turned "on".  
5) Flash-1x & Pause = 1 transmitter code is stored in the system's memory.  
6) Flash-2x & Pause = 2 transmitter codes are stored in the system's memory.  
7) Flash-3x & Pause = 3 transmitter codes are stored in the system's memory.  
8) Flash-4x & Pause = 4 transmitter codes are stored in the system's memory.  
10) Flash-2x & Pause = The security system was triggered from the hood or  
trunk circuit.  
11) Flash-3x & Pause = The security system was triggered from the door circuit  
.
12) Flash-4x & Pause = The security system was triggered from the Auxiliary  
Sensor Port circuit.  
Au d ible An d Visu a l In d ica tion s  
The Security system's audible output and the vehicle's parking and interior lights  
are utilized to indicate a number of events or processes associated with the system's  
operation:  
1) One siren chirp and one light flash upon closing the vehicle's door: The system  
has started a passive Last Door Arming countdown and will become armed after  
the 30 second countdown expires. This chirp indicates that the starter interrupt  
will engage and the doors will lock when the alarm becomes fully armed in 30  
seconds.  
Zone Violation: If the system is triggered, the LED Status Indicator will start  
toflashandpauseoneofthefollowingsequencestoindicatewhichprotectedcircuit  
triggered the system. This is seen while the system is armed, and after disarming,  
until the ignition switch is turned "on", which will clear the Zone Violation code.  
The unit's memory can store two different violation codes.  
9) Flash-1x & Pause  
= The security system was triggered from the current  
2) One siren chirp, one light flash, & doors lock: The system has armed passively  
sensing circuit.  
or actively from the transmitter. The starter interrupt has engaged and the doors  
Page - 17  
Page - 18  
have locked. The optional sensor will become operational 5 seconds later.  
L I M I T E D L I F E T I M E W A R R A N T Y  
3) One siren chirp after the arming chirp previously mentioned: The auxiliary  
sensor circuit is bypassed by pressing the small transmitter button within 3  
seconds of pressing the large transmitter button.  
Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company), are  
warranted to be free from defects in materials and workmanship under normal use. If a product sold by the Company  
proves to be defective, the Company will repair or replace it free of charge within the first year and thereafter all  
parts to be repaired will be free with only a nominal charge for Omega Research and Development, Inc.'s labor and  
return shipping, to the original owner during the lifetime of the car in which it was originally installed.  
All products for warranty repair must be sent postage prepaid to Omega Research & Development, Inc., P.O.  
Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof of purchase. This warranty is  
nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or abuse,  
improper installation, alteration, any use contrary to its intended function, unauthorized service, fire, flood,  
lightning, or other acts of God.  
4) One siren chirp, and no light flash, but only at the moment the ignition switch is  
turned "off": The alarm is in Valet Mode, and will not arm actively or passively.  
This warranty limits the Company's liability to the repair or replacement of the product. The Company shall  
not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its contents, or any  
incidental or consequential damages caused by any failure or alleged failure of the product to function properly.  
Under No Circumstances Should This Warranty, Or The Product Covered By It, Be Construed As A Guarantee Or  
Insurance Policy Against Loss. The Company neither assumes nor authorizes any person or organization to make  
any Warranties or assume any liability in connection with the sale, installation, or use of this product.  
5) Two siren chirps and the parking lights stay on for 30 seconds:  
The system has just disarmed or 2nd channel output has been activated.  
6) Two siren chirps and two light flashes: The system has entered the Valet Mode.  
7) Four siren chirps and the lights stay on for 30 seconds: The system has just  
disarmed and was activated while you were away. The system will have this  
disarming confirmation until the ignition switch is turned "on".  
This device complies with FCC Rules part 15. Operation is subject to the following two  
conditions, (1) This device may not cause harmful interference and, (2) This device must  
accept any interference that may be received, including interference that may cause  
undesired operation.  
The manufacturer is not responsible for any radio or TV interference caused by unautho-  
rized modifications to this equipment. Such modifications could void the user's authority to  
8) Sirensounding, changingsoundsevery5seconds, andtheparkinglightsflashing  
on and off: The system is in an activated state. This will also relock the doors.  
operate the equipment.  
continued on page 22  
Page - 19  
MO_K9-6ATV2  
 
cotninuedfmorapge19  
Features Programming Checklist  
This checklist helps when programming features. Before  
attempting feature programming, please carefully read pages  
27-38tobecomefamiliarwiththefeaturesandtheprogramming  
procedure.  
To best use this checklist, mark each applicable box with "\"  
next to the feature to be changed before entering Features  
Programming Mode. As each feature is programmed, change  
its mark to "X".  
To program features, follow these steps:  
Step1-Turntheignition"off",andpressthevaletswitch5times.  
(the system will respond a chirp, then briefly sounding the  
siren and the Status LED begins flashing)  
Step2- Pressthevaletswitchthesamenumberoftimesasthe  
feature number.  
(the system will acknowledge the valet switch entry by  
repeating the same number of siren chirps and the Status  
LED flashes a like amount)  
Step 3 - Pressthetransmitter'scenterbuttontoturnthefeature  
"on", or press the left button to turn the feature "off".  
(turning the feature "on" is indicated by one horn chirp and  
theStatusLEDbeingon;turningthefeature"off"isindicated  
by two horn chirps and the Status LED being off)  
Repeat - Steps 2 and 3 for each feature to be changed  
#
FEATURE  
DEFAULT  
1
Ignition-Activated Anti-Carjacking Protection  
Door-Activated Anti-Carjacking Protection  
Last Door Arming  
OFF (left button)  
OFF (left button)  
ON (center button)  
ON (center button)  
ON (center button)  
ON (center button)  
ON (center button)  
OFF (left button)  
ON (center button)  
2
3
4
Doors Lock With Last Door Arming  
Current Sensing  
5
6
Doors Lock At Ignition "On"  
Unlock #1 At Ignition OFF  
7
8
Unlock #2 At Ignition OFF  
9
Open Door Bypass To Features #6, #7, #8  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Lights On 5 / 30 Seconds Upon Disarm 30 Seconds (center button)  
Automatic Rearming  
ON (center button)  
ON (center button)  
2nd Channel Output Disarms System  
.8 / 3 Second Doorlock Pulse  
Double Unlock Pulse  
.8 Second (center button)  
OFF (left button)  
3 / 45 Second Arming Delay  
Confirmation Chirp  
3 Second (center button)  
ON (center button)  
30 / 60 Second Activated Alarm Cycle 60 Seconds (center button)  
Pulsed Horn / Steady Siren Output  
Loud / Soft Pulsed Horn Chirps  
Total Closure Lock Output  
Steady Siren (left button)  
Loud (center button)  
OFF (left button)  
Remote-Activated Anti-Carjacking Protection  
OFF (left button)  
One / Two Button Arming / Disarming One Button (center button)  
If no programming activity occurs within a 10 second  
period, the Features Programming Mode will expire.  
ThesystemexitingFeaturesProgrammingModeisindicatedby  
the siren briefly sounding.  
 
The Anti-Carjacking feature automatically activates for each of the three  
described conditions, provided that each has been programmed to operate. In each  
of the three methods, the vehicle operator has 53 seconds to press the Valet Switch  
to cancel the Anti-Carjacking feature. If not cancelled, at 53 seconds the siren will  
start chirping, to remind the operator that Anti-Carjacking will engage. This will  
continue for 7 seconds, during which time the Anti-Carjacking feature may still be  
cancelled by pressing the Valet Switch. At 60 seconds, the Anti-Carjacking feature  
fully engages, sounding the siren and flashing the parking lights. Thirty seconds  
after the siren sounds and the parking lights flash, the starter interrupt will engage.  
During this 30 second period, if the ignition is turned "off" the starter interrupt will  
instantly engage.  
Option a l P a ger Un it An d Ba cku p Ba tter y  
This security system is designed for easy compatibility with the Omega Pager  
unit and also for a Backup Battery (both of which are optional additional compo-  
nents). The Omega Pager will alert the user to a security system violation, and also  
indicate which protected zone caused the violation. The Backup Battery option will  
allow the security system to operate even if power is removed from the system's  
control module or if the vehicle's battery is disconnected. The Omega dealer from  
which you purchased your vehicle security system can provide more details on the  
exact operations of each of these options.  
P r ogr a m m in g Tr a n sm itter s  
When adding or deleting transmitter codes to operate the security system,  
follow this process:  
Once fully activated, the Anti-Carjacking feature can only be deactivated by  
turning the ignition "off", then "on" again, after which the Valet Switch must be  
pressed within 5 seconds. When the Anti-Carjacking feature is fully engaged, the  
system will not respond to the transmitters, nor will it automatically reset after 60  
seconds. The Anti-Carjacking operation will continue until deactivated or until the  
vehicle's battery is drained.  
1) Turn "on" the ignition.  
2) Within5secondsofturning"on"theignition,presstheValetSwitch5times.The  
siren will chirp, confirming that for the next 10 seconds the system is ready to  
learn a transmitter code. When the first transmitter code is learned all existing  
storedcodeswill be erased. Toentera transmittercode, simply press andrelease  
Page - 24  
Page - 25  
the transmitter button which is desired to arm and disarm the system.  
P r ogr a m m in g Fea tu r es  
Your vehicle security system has 22 programmable features that allow your  
system to be customized to fit your personal needs. To program these features "on"  
or "off", follow this process:  
3) Repeatthisprocedureforeachtransmitterdesiredtooperatethesecuritysystem.  
The system will chirp the siren once to confirm that each transmitter code was  
learned. Both of the other two transmitter button's functions will automatically  
be learned when the arm / disarm button is learned. If a code is not received  
within a 10 second period, the learning process will automatically terminate.  
1) Turn "off" the ignition.  
2) Within 5 seconds of turning "off" the ignition, press the Valet Switch 5 times.  
The siren will chirp, followed by a short siren burst, confirming that for the next  
10 seconds the system is ready to receive a feature number.  
Although this security system is programmed at the factory for the large center  
transmitter button to arm and disarm the system, any one of the transmitter's three  
buttons may be programmed to arm and disarm the security system. Upon the  
system learning the arm / disarm button, the other two buttons are automatically  
assigned other functions, as follows:  
3) Press the Valet Switch the number of times that is equal to the feature number.  
Example: Press the Valet Switch six times if Feature #6 is to be changed.  
Arm / Disarm  
Large Center Button  
Small Right Button  
Small Left Button  
Trunk Release  
Small Right Button  
Large Center Button  
3rd Channel  
4) The siren will respond by chirping the same amount as the feature number.  
Example: The siren responds with six chirps.  
Small Left Button  
Small Left Button  
Small Right Button  
5) Press the large transmitter button to turn the feature "on". When done, the siren  
will respond with one chirp.  
Large Center Button  
Page - 26  
Page - 27  
 
6) Press the small left transmitter button to turn the feature "off". When done, the  
siren will respond with two chirps.  
15)  
16)  
17)  
18)  
19)  
20)  
21)  
22)  
3 / 45 Second Arming Delay: Default 3 Seconds.  
Confirmation Chirp: Default ON.  
30 / 60 Second Activated Alarm Cycle: Default 60 Seconds.  
Pulsed Horn / Steady Siren Output: Default Steady Siren.  
Loud / Soft Pulsed Horn Chirps: Default Loud.  
Total Closure Lock Output: Default OFF.  
If the Valet Switch is not pressed or if a transmitter signal is not received within a  
10 second period, the Programmable Features learning process will automatically  
terminate. The 22 Programmable Features are:  
Remote-Activated Anti-Carjacking Protection: Default OFF.  
One / Two Button Arming / Disarming: Default One Button.  
1)  
2)  
3)  
Ignition-Activated Anti-Carjacking Protection: Default OFF.  
Door-Activated Anti-Carjacking: Default OFF.  
Last Door Arming: Default ON.  
4)  
5)  
Doors Lock With Last Door Arming: Default ON.  
Current Sensing: Default ON.  
P r ogr a m m a ble Fea tu r es  
6)  
7)  
8)  
9)  
10)  
11)  
12)  
13)  
14)  
Doors Lock At Ignition "On": Default ON.  
Unlock Output #1 At Ignition "Off": Default ON.  
Unlock Output #2 At Ignition "Off": Default OFF.  
Open Door Bypass To Features #6, #7, #8: Default ON.  
Lights On 5 / 30 Seconds Upon Disarm: Default 30 Seconds.  
Automatic Rearming: Default ON.  
2nd Channel Output Disarms System: Default ON.  
.8 / 3 Second Doorlock Pulse: Default .8 Second.  
Double Unlock Pulse: Default OFF.  
Feature #1: Ignition-Activated Anti-Carjacking Protection  
(Factory Setting: OFF)  
FeatureTurnedOn:Afterturningtheignitionswitch"on"andstartingthevehicle,  
youmustpresstheValetSwitchwithin60seconds.IftheValetSwitchisnotpressed  
the security system will begin chirping the siren 53 seconds after the ignition was  
turned"on". ThesechirpsaretoremindyouthatAnti-Carjackingisabouttoengage;  
pressing the Valet Switch during the chirps will cancel the Anti-Carjacking feature.  
Thechirpswilllastfor7seconds, afterwhichtimethesirenwillsoundcontinuously  
and the parking lights will begin flashing to attract attention to the vehicle.  
Page - 29  
Page - 28  
Thirty seconds after the siren and parking lights engage, or if the ignition is turned  
"off", the starter interrupt will engage. Once the Anti-Carjack is engaged, the only  
way to disengage it is to turn the ignition "off", then back "on" again, and then press  
the Valet Switch within 5 seconds. Altogether, there are three Anti-Carjacking  
Programmable Features, which may be programmed independently.  
Automatic Last Door Arming feature will be interrupted. When the instant trigger  
becomes ungrounded, the security system will become fully armed thirty seconds  
later. All of the doors and the trunk must have the proper connection of the control  
module's wiring. This feature allows unhurried passenger exit and trunk access, as  
the Last Door Arming process does not start until the last door or trunk is closed,  
and opening any door or the trunk will interrupt the process. You can still actively  
arm the security system with the transmitter at any time.  
Feature #2: Door-Activated Anti-Carjacking Protection  
(Factory Setting: OFF)  
Feature Turned On:This feature operates the same as the Anti-Carjacking feature  
described above, except that opening a door while the ignition is "on" will initiate  
the 60 second Anti-Carjacking cycle.  
Feature #4 Doors Lock With Last Door Arming  
(Factory Setting: ON)  
Feature Turned On: When the security system passively arms from the Last Door  
Armingfeature, thedoorswillalsolockifanoptionaldoorlockinterfacewasadded.  
This will occur when the system becomes fully armed 30 seconds after closing the  
last door. Feature #3 must be on in order for this feature to operate.  
Feature #3: Last Door Arming  
(Factory Setting: ON)  
Feature Turned On: The security system will arm itself automatically when the  
vehicle'slastdoorisclosed. Atthemomentthelastdoorisclosedthesirenwillchirp  
the exterior lights will flash once, and the Status LED will flash fast. Thirty seconds  
later the siren will chirp once again, the lights will flash, and the Status LED will  
flash slowly, indicating that the security system is fully armed. If feature #4 is  
selected, the doors will also lock at this time. If the instant trigger is grounded at any  
time during the thirty second countdown (Example: opening the trunk), the  
Feature #5: Current Sensing  
(Factory Setting: ON)  
FeatureTurnedOn: Whenthesecuritysystemisarmed,currentsensingcandetect  
a positive current draw from the vehicle's battery. (Example: the dome light comes  
on when a door is opened or the brake lights come on when the brake pedal is  
pressed). With this feature on, the security system will trigger if a current draw is  
detected.  
Page - 30  
Page - 31  
 
Feature #6: Doors Lock At Ignition "On"  
(Factory Setting ON)  
Feature #9: Open Door Bypass To Features #6, #7, #8 (Factory Setting ON)  
Feature Turned On: When the security system locks and unlocks the doors from  
Features #6, #7 and #8, if a door is open the doors will not automatically lock when  
the ignition switch turns "on", or automatically unlock when the ignition switch is  
turned "off".  
Feature Turned On: The security system will automatically lock the vehicle's  
doors one second after the ignition switch is turned "on". This feature adds  
considerable personal security to you and your family.  
Feature #7: Unlock Output #1 At Ignition "Off"  
Feature #8: Unlock Output #2 At Ignition "Off"  
(Factory Setting ON)  
(Factory Setting OFF)  
Feature #10: Lights On 5 / 30 Seconds Upon Disarm  
(Factory Setting 30 Seconds)  
Feature Turned On: Upon disarming, the exterior and interior lights will stay on  
for 30 seconds, to illuminate the way to your vehicle.  
Feature Turned Off: The exterior and interior lights will stay on for 5 seconds  
when the system is disarmed.  
These Features will cause the security system to automatically unlock either the  
driver's door or all of the vehicle's doors instantly when the ignition switch is turned  
"off". Please note that the exact operating parameters of these Features depends  
upon the configuration of the security system and your vehicle's power doorlocks.  
This system may be configured to unlock only the driver's door upon disarming.  
Then if desired, pressing the large transmitter button again within 5 seconds will  
unlock all of the doors. These Features can operate one of two ways: first, if all of  
the doors unlock upon disarming, these Features will unlock all of the doors  
when the ignition is turned "off". Second, if your vehicle is configured to unlock the  
driver's door only upon disarming, these Features can be configured to unlock only  
the driver's door upon the ignition being turned "off". Please consult with the  
installer as to the feasibility of adding the driver's door only unlock configuration  
toyourvehicle, aspowerdoorlockingsystemsdifferincompatibilitytothisfeature.  
Feature #11: Automatic Rearming  
(Factory Setting ON)  
Feature Turned On: When the transmitter has disarmed the security system, the  
system will rearm and relock the doors 90 seconds later, unless a door is opened or  
the ignition is turned on. This feature prevents the system from being accidentally  
disarmed if a transmitter button is unknowingly pressed by an object while in a  
pocket or purse, or from children playing with the transmitter.  
Page - 32  
Page - 33  
Feature Turned Off: When the transmitter has disarmed the security system, the  
Feature #15: 3 / 45 Second Arming Delay  
(Factory Setting 3 Seconds (ON)  
system will stay disarmed until the transmitter is used to arm it again.  
Feature Turned On: The security system will be become fully armed 3 seconds  
after the arming siren chirp confirmation.  
Feature #12: 2nd Channel Output Disarms System  
(Factory Setting ON)  
Feature Turned Off: The security system will be become fully armed 45 seconds  
after the arming siren chirp confirmation.  
Note: During the arming delay if any protected circuit should go into a triggered  
state, the system will arm, but that circuit will be unprotected until it reverts back  
to an non-triggered state.  
Feature Turned On: When the 2nd channel output is utilized, the security system  
will also disarm at the same time, chirping the siren twice, unlocking the doors and  
turning the exterior lights on for thirty or five seconds. The 2nd channel output, and  
this feature, can be used for remote trunk release operation.  
Feature #13: .8 / 3 Second Doorlock Pulse  
(Factory Setting .8 (ON)  
Feature #16: Confirmation Chirp  
(Factory Setting ON)  
Feature Turned On: The doorlock outputs have a .8 second negative pulse to an  
optional doorlock interface to operate the vehicle's power doorlocking system.  
Feature Turned Off: The doorlock outputs have a 3 second negative pulse to an  
optional doorlock interface to operate the vehicle's vacuum doorlocking system.  
Feature Turned On: The security system will chirp the siren for confirmation that  
the system armed and disarmed.  
Feature Turned "Off": The security system will not have siren chirps for the  
arming and disarming confirmation. Turning this feature off will also eliminate the  
threechirpsuponarmingiftheinstanttriggercircuitisgrounded, andthefourchirps  
upondisarmingifthesystemwastriggeredandreset.However,thePrewarnFeature  
and the Programmable Features chirps will still operate.  
Feature #14: Double Unlock Pulse  
(Factory Setting OFF)  
Somenewervehiclesrequireadoorlockinterfacewhichprovidesadoubledoorlock  
output pulse to unlock all of the vehicle's doors. Feature #12 must be .8 second  
doorlock pulse time (Feature #12 turned ON) for Feature #14 to operate.  
Feature Turned On: The unlock output provides two pulses.  
Regardless of this Feature, eliminating the siren chirp may be done on a onetime  
temporary basis as desired by pressing the small left transmitter button twice for  
arming or disarming. Even if this Feature is used to remove the confirmation chirps,  
Feature Turned Off: The unlock output provides a single pulse.  
the audible Automatic Transmitter VerificationTM feature will still operate.  
Page - 34  
Page - 35  
 
Feature #17: 30 / 60 Second Activated Alarm Cycle  
(Factory Setting 60 Seconds (ON)  
Feature Turned On: Upon activation, the siren will sound and the parking lights  
will flash for 60 seconds.  
Feature Turned Off: Upon activation, the siren will sound and the parking lights  
will flash for 30 seconds.  
Feature #19: Loud / Soft Pulsed Horn Chirps  
Feature Turned On: 12 Millisecond Confirmation Honks.  
Feature Turned Off: 8 Millisecond Confirmation Honks.  
If your security system is configured to use the vehicle's horn, this Feature allows  
a degree of compensation for the variance which is found in the length of the pulse  
required to honk the horn in a satisfactory manner.  
(Factory Setting Loud (ON)  
Please note that the shorter 30 second activated time may be required in some  
localities to comply with noise nuisance ordinances.  
Feature #20: Total Closure Lock Output  
Feature Turned On: 28 Second Doorlock Output.  
Feature Turned Off: .8 Second Doorlock Output.  
(Factory Setting OFF)  
Feature #18: Pulsed Horn / Steady Siren Output  
If the vehicle is so equipped, this Feature allows the installer to take advantage of  
a preexisting Total Closure System.  
(Factory Setting Steady Siren (OFF)  
Feature Turned On: This Feature allows the use of the vehicle's horn in place of  
the electronic siren for the audible output of the security system. When configured  
for use with a horn, this output pulses for 10 seconds, then pauses for 5 seconds,  
repeating this cycle for the duration of the activated alarm period. This prevents  
the horn from overheating, thereby ensuring a maximum useful life to the vehicle  
owner.  
Feature Turned Off: The output is a continuous, steady output which the elec-  
tronic siren requires. The siren features six different siren tones, which change  
every 5 seconds.  
Feature #21: Remote-Activated Anti-Carjacking Protection  
(Factory Setting OFF)  
Feature Turned On: Anti-Carjacking Protection Feature Activated By 3rd  
Channel Output. This Feature allows remote activation of the Anti-Carjacking  
Feature. If this Feature is turned ON, pressing the Small Left Button on the trans-  
mitter for 3 seconds will activate the Anti-Carjacking Feature, but only when the  
ignition switch is "on". This Feature may be activated regardless of the setting of  
Features #1 and #2 (Ignition and Door Activated Anti-Carjacking Protection).  
Page - 36  
Page - 37  
Feature Turned Off: 3rd Channel Will Not Operate Anti-Carjacking.  
Tr a n sm itter Option s  
Feature #22 configured for  
"Two Button Arming / Disarm-  
ing" with supplied transmitter  
Optional 4-button transmitter with  
Feature #22 configured for "Two  
Button Arming / Disarming"  
Feature #22: One / Two Button Arming / Disarming  
(Factory Setting One Button (ON)  
Feature Turned On: One Button Arming / Disarming. This Feature controls  
how the transmitter operates the security system. If this Feature is turned ON, the  
transmitter's Large Center Button will alternate arming and disarming the system  
with each press of the button. This type of operation is also described as a "single  
button toggle" for the arming and disarming of the system.  
Feature Turned Off: Two Button Arming / Disarming. Having this Feature set  
to the OFF setting causes the system to operate in a "dedicated button for arming  
and dedicated button for disarming" fashion. This Feature's "Two Button" setting  
may be used with the standard 3-button transmitter; when configured in this fashion  
the large center button arms the system, and the small right button disarms the  
system. Pressing the small right button operates trunk release; pressing the large  
center button and small right button together operates the 3rd channel output.  
Arms system, and engages  
Operates  
Arms system, and  
engages "panic"  
with  
"panic" with system armed  
2nd channel  
output  
Disarms  
system  
system, and  
engages  
"panic"  
with  
armed  
J
JJ  
K -  
9
Operates  
2nd channel  
output  
II  
III  
system  
disarmed  
Operates  
3rd channel  
output  
Enhanced "Panic" operation: Having feature #22 configured for "Two Button  
Arming / Disarming" enhances the "Panic" feature's operation; using the "arm"  
button activates "Panic" with an armed system, locking the doors, and using  
Optional 4-button trans-  
mitter for K9-6ATV2 is  
part number #105-07  
K9-6ATV2 434MHz w/Green LED (#103-01)  
"disarm" button results in "Panic" with a disarmed system and unlocked doors.  
Page - 38  
Page - 39  
 

Miele Microwave Oven H 4084 BM User Manual
MTD Trimmer YM90BC User Manual
MTX Audio Speaker T5508 44 User Manual
Murphy Switch PVM Series User Manual
NETGEAR Network Router DG834 User Manual
Omega Speaker Systems Power Supply FAR 1 Series User Manual
Omnimount TV Mount OM10049 User Manual
Omnimount TV Mount PLAY40 User Manual
Panasonic Blu ray Player DMP BD77 User Manual
Parkside Paint Sprayer PFS 100 A1 User Manual